Insulated & Refrigerated Vans

Van Cars Insulation & Supplying Units

(As The Van Sizes Or Model)

Insulated and Refrigerated Vans, All Types & Sizes Of Van Cars, Rear cabin preparation and insulation / polyurethane with a thickness of (5) cm, fiber insulation and installation of a cooling unit for a van (thickness 5 cm)

- In our factory, VOLGA we produce, design, manufacture our own cooling and freezing units with suitable boxes, all supported by American technologies from VOLGA.USA, a leader in cooling technologies.
- Preparing and installing transport and storage boxes under the globally leading brand VOLGA COOLING TECHNOLOGIES USA. VOLGA HVAC ^®

Cooling unit specifications:
Installation of a Volga car cooling unit, model VT-380T
Technical specifications of the unit
The cooling unit comes from the American company VOLGA COOLING TECHNOLOGIES, USA.
Brand: VOLGA HVAC® Saudi assembly - Global Cooling Tower Factory.
Air flow rate: 1600 m3/hr, the highest in its class.
Cooling power: from zero degrees Celsius to plus five 0 c TO +5 c As The Van Sizes.
Freezing power: from zero degrees Celsius to - 18 As The Van Sizes.
External condenser: copper tubes / copper fins.
Internal evaporator: copper tubes / treated copper fins / antimicrobial resistant.
Compressor: 5S14 Approved: CTI.
Air flow/ Parallel – (Recommended)..
Number of fans in the indoor unit: 2 / Cooling coverage from 8 to 12 cubic meters.
Number of fans in the outdoor unit: 1/ Or More As The Van Sizes.
Capacity / resistance to withstand an external ambient air temperature of 59 degrees Celsius.
Defrosting feature: Hot Gas Defrusting.
Voltage: DC 12V – 24V.
Refrigerant content: 1.2 kg – 134a/ 410/407C As The Van Sizes.
External unit size: 930 mm x 720 mm x 190 mm (As The Van Sizes Or Model).
Internal unit size: 1010 mm x 570 mm x 150 mm, (As The Van Sizes Or Model).
Weight: External/ 23.5 kg Internal/ 15 kg.

Cabin specifications:

First: Insulating the cargo cabin:-

1- Insulating the cabin sides with sandwich panels with a thickness of (4.8) cm. And additional insulation with fiberglass 4 layers
2- Insulating the cabin ceiling and doors - by direct injection - with polyurethane with a thickness of (4.8) cm. Additional insulation with fiberglass 4 layers
3- Insulate the cabin floor with panels - and direct injection with polyurethane with a thickness of (5.2) cm. Additional insulation with fiberglass 4 layers
- 4 Treat the floor with Heresite paint (phenolic resin) in two layers, then apply a final layer of resistant epoxy paint for the entire floor and the lower part of the sides with a height of 7-10 cm
Second: The floor:-
1- Insulate the cabin floor with three levels:
1- Polyurethane panels with a thickness of (5) cm
2- Resistent moisture and heat wood with a thickness of 18-20 mm.
3- Pour and install 4 layers of fiberglass (fiberglass). For the floor to withstand high loads and shocks.
4- Paint the lower part of the cabin with Heresite phenolic resin paint in two layers and an epoxy paint layer.
2- Dimensions of the inner box area (length 1.80 meters x width 1.40 meters x height 1.45 meters)

Third: Specifications of the insulating panels:-

The wall, ceiling and floor panels are made of (Prefabricated panels) approved by VOLGA COOLING TECHNOLOGIES, and conform to Saudi and American specifications and have obtained CTI approval and certification.

• Thickness of the insulating material: 5 cm. (Total thickness from 4.9- 5.3 cm)
• Type of insulating material: Polyurethane / Actual density not less than 38-40 kg/m3.

• Thermal insulation coefficient: 0.02 W/m/°C

Inner covering:-
- Made of fiberglass, reinforced with epoxy resistant to water, moisture and shocks.

We Making The Inner Van Boxes refrigeration units: Cooling And Freezing from Volga Company VOLGA HVAC ®

All Volga refrigeration units, VOLGA COOLING TECHNOLOGIES. whether Cooling or freezing units, are equipped with a full-access digital control control and are installed inside the vehicle’s cabin, allowing full access to control from turning off and on the unit to the possibility of full control to configure the unit and settings and control and read the required temperatures.
The units are equipped with a reciprocating type compressor *Other options available that runs on the car engine *other options are available, and the unit can also be equipped with a compressor that operates on alternating current according to the customer’s request.
The external unit is installed on the appropriate side - depending on the model and design of the car for the cooling boxes and is designed inside a dynamic - streamlined body made of fiberglass * Other options are available, in line with the appearance of the car, specially developed and designed by the Global Cooling Tower Factory in cooperation with the American Volga Cooling Technologies Company . Under the world's leading brand in the field of refrigeration and air conditioning, our devices have already proven their very high capabilities in withstanding harsh weather conditions of high temperatures, humidity, and sand storms.
The internal unit is also equipped with an evaporator produced by Volga Company - a Saudi industry, which is installed inside the box within a fiberglass frame. *Other options are available,